The Telegram Expert interface allows convenient IP Service management — uploading, checking, or removing them from the general list. The user can manually control the status of each entry: all information is presented in table format with quick evaluation and action options.
Table columns:
1. host – displays the IP address or domain name of the server to which the program connects via Privacy service.
2. port – shows the numerical port number used to access the internet through the given anonymity service.
3. login – contains the login required to authorize through the IP Solution server.
4. password – displays the password needed to access the specific IP Service.
5. type – shows the type of connection used: HTTP or SOCKS5.
6. version – reflects the IP version used by the IP Solution (only IPv4 is supported).
7. response – indicates how quickly the server responds to a request (response time in milliseconds).
8. status – visually shows whether the IP Service passed the check: «ok» means the connection is established, «bad» means the connection failed.
9. actions – in this column, you can manually launch a check for a specific network routing or delete it from the list.
The software works only with IPv4 connections.
The user can select one or multiple rows from the table and resend the connections for verification or delete them. This is especially convenient for cleaning up non-working connections after the initial check.
If you are sure the connections should be working, but you received a «bad» status during the check, test them in practice — for example, by trying to log into an account. Sometimes the system may incorrectly mark the connection as unavailable, especially if there are network delays.
Also, if you notice unstable connection speeds in your region, it’s recommended to increase the response timeout to 45 seconds and set the connection attempt limit to 15 in the software settings. This may help reveal that previously «red» connections actually work normally. Reliable connections always pass testing stably.
New addresses are added below. You need to select the required connection type, and then enter the data in the format: ip
ort:loginassword. After that, click the add button — the system will check the entered values and, if no errors are found, will add them to the table.
IP solution usage setup:
– If you select «Take IP service from settings» in the «Work through network solution» section, the software will randomly use the connections from the general list described above.
– If you select «Take IP service from account», the IP service will be linked to a specific account. Go to the account panel, select the necessary profiles, click «Select action,» then «Add network solution,» and enter the data in the standard format.
– If the setting is «Disabled», the software will use your provider’s IP address during operation.
Table columns:
1. host – displays the IP address or domain name of the server to which the program connects via Privacy service.
2. port – shows the numerical port number used to access the internet through the given anonymity service.
3. login – contains the login required to authorize through the IP Solution server.
4. password – displays the password needed to access the specific IP Service.
5. type – shows the type of connection used: HTTP or SOCKS5.
6. version – reflects the IP version used by the IP Solution (only IPv4 is supported).
7. response – indicates how quickly the server responds to a request (response time in milliseconds).
8. status – visually shows whether the IP Service passed the check: «ok» means the connection is established, «bad» means the connection failed.
9. actions – in this column, you can manually launch a check for a specific network routing or delete it from the list.
The software works only with IPv4 connections.
The user can select one or multiple rows from the table and resend the connections for verification or delete them. This is especially convenient for cleaning up non-working connections after the initial check.
If you are sure the connections should be working, but you received a «bad» status during the check, test them in practice — for example, by trying to log into an account. Sometimes the system may incorrectly mark the connection as unavailable, especially if there are network delays.
Also, if you notice unstable connection speeds in your region, it’s recommended to increase the response timeout to 45 seconds and set the connection attempt limit to 15 in the software settings. This may help reveal that previously «red» connections actually work normally. Reliable connections always pass testing stably.
New addresses are added below. You need to select the required connection type, and then enter the data in the format: ip
ort:loginassword. After that, click the add button — the system will check the entered values and, if no errors are found, will add them to the table.IP solution usage setup:
– If you select «Take IP service from settings» in the «Work through network solution» section, the software will randomly use the connections from the general list described above.
– If you select «Take IP service from account», the IP service will be linked to a specific account. Go to the account panel, select the necessary profiles, click «Select action,» then «Add network solution,» and enter the data in the standard format.
– If the setting is «Disabled», the software will use your provider’s IP address during operation.
Важно: информация, сервисы и материалы, размещенные на форуме, предназначены исключительно для ознакомительных и информационных целей. Пользователи самостоятельно оценивают законность и допустимость их использования с учетом законодательства применимой к ним юрисдикции, а также правил соответствующих сервисов и платформ.
Последнее редактирование модератором: